Shape-memory alloys.
Metals that remember their shape.
A shape-memory alloy campaign finds alloys that change shape at the temperature you choose and recover the strain your part needs.


- Actuators
- Superelastic devices
- Couplings and dampers
- Magnetic actuators
Why this domain matters to your work.
Shape-memory alloys recover a large strain when their crystal structure changes, so a wire, spring or tube can act as an actuator, a coupling or a damper with no moving parts beyond the metal itself. NiTi is the workhorse for actuators and superelastic devices, high-temperature nickelides with palladium, platinum, gold, hafnium or zirconium push actuation above 100 °C, Cu–Al–Ni bronzes offer low-cost superelastic crystals, and Ni–Mn–Ga Heuslers change shape in a magnetic field. The transformation temperature decides where each alloy can work.
The transformation temperature is very sensitive to composition, so a small change in nickel content or a third element can move it a long way. Narrow hysteresis helps fast, efficient cycling but is hard to keep while adding strain or raising the working temperature. High-temperature nickelides lean on precious metals or hafnium, which raises cost and supply risk, and copper-based alloys are cheap but brittle as polycrystals. Field-driven strain in Ni–Mn–Ga is large in single crystals and hard to keep in practical parts.
A campaign lets your team name the transformation temperature, the recoverable strain and the hysteresis you can accept, field-driven actuation if you need it, and cost. You receive ranked NiTi, high-temperature nickelide, Cu–Al–Ni and Ni–Mn–Ga candidates with estimated transformation temperature, hysteresis, recoverable strain, field-driven strain, stiffness and cost. These are screening estimates, not calculations for the new alloy, and Cu–Zn–Al and iron-based alloys are not covered. Processing, precipitation, functional fatigue and two-way memory are decided by making the alloy and cycling it.
The material families this domain searches.
Each family brings its own structures and chemistry to the search. A campaign can search one of them or compare several under the same targets.
NiTi nickelides
Nickel–titanium alloys, with copper and other solutes, chosen as the established classics for actuators and superelastic devices.
High-temperature nickelides
NiTi alloyed with palladium, platinum, gold, hafnium or zirconium, chosen for actuators that must work above 100 °C.
Cu–Al–Ni bronzes
Copper–aluminum–nickel crystals, chosen for low-cost superelastic behavior at higher temperatures, though they are brittle as polycrystals.
Ni–Mn–Ga Heuslers
Nickel–manganese–gallium alloys whose crystal structure moves in a magnetic field, chosen for actuators driven by a field instead of heat.
The properties a campaign can aim for.
Choose the properties that matter to your work. For each one, say whether a candidate must meet it or should push it as far as it goes, with cost and supply always in view.
- Recoverable strain
- Transformation temperature
- Low hysteresis
- Strain driven by a magnetic field
- Stiffness
- Cost and supply risk
Starting points for a campaign.
Each starting point sets up a campaign for a common goal in this domain. Begin from one and adjust its targets, or set your own from the start.
Ambient and body-temperature actuators
Suits actuator designers working near room or body temperature, holding the transformation between 250 and 400 K.
Superelastic devices
Suits makers of superelastic parts, searching for alloys that combine narrow hysteresis with high recoverable strain.
High-temperature actuators
Suits actuators in hot surroundings, searching for alloys that transform and actuate above the boiling point of water.
Magnetic shape-memory actuators
Suits teams building field-driven actuators, ranking Ni–Mn–Ga alloys on the strain a magnetic field can produce.
Low-cost shape-memory alloys
Suits cost-driven products, searching copper-based shape-memory alloys that contain no precious metal at all.
What you specify, what you receive and where the figures stop.
MS Lattice hands your lab a shortlist to make and test. Its figures are screening estimates and calculations, not measurements of the new material, and each domain says where they stop.
You specify
The transformation temperature, the recoverable strain and the hysteresis you can accept, field-driven actuation if you need it, and cost.
You receive
Ranked NiTi, high-temperature nickelide, Cu–Al–Ni and Ni–Mn–Ga candidates, with estimated transformation temperature, hysteresis, recoverable strain, field-driven strain, stiffness and cost.
Before you rely on it
The transformation figures are screening estimates, not calculations for the new alloy. Processing, precipitation, functional fatigue and two-way memory are not predicted, and Cu–Zn–Al and iron-based alloys are not covered.
The same four modes work in every domain.
Search from your targets alone, improve a material your team already uses, or watch the engine reach known materials, with the targets as guides or sealed away, to see how well it searches.
Open Discovery
Choose it when you know what the material must do but have no starting structure.
Prototype-Guided Optimization
Choose it when you already have a good material and want to make it better.
Guided Rediscovery
Choose it when you want to watch the engine reach a material you already know.
Blind Rediscovery Benchmark
Choose it when you want to test whether the engine finds an answer it was never shown.
Every candidate arrives with its record.
Each candidate comes ranked against your targets, with its estimated properties and their uncertainty, the checks it passed and a structure file to export, ready for your lab.
Questions teams ask about this domain.
Have a materials target? Tell us what it must do.
Share the material domain, the properties you need and the limits the material must respect. We will show you how MS Lattice would approach it through Norck, from a ranked shortlist for your own lab all the way to finished parts.

